Description
Flight Controller designed by racers. The Wizz F7 FC is perfect for racing freestyle or cruising.
Analogue or Digital the Wizz F7 has got you covered with the option to connect to analogue VTX and Cameras or connect to a Dji unit via the dedicated connector.
Never worry about adding LEDs to your drone for FAI races. Up to 40 LEDs can be directly connected to the 4 corners of the FC and control output colours directly from betaflight.
Specifications:
• Size: 20*20 M3 holes with vibration damping
• MCU: STM32F722RET6 216MHz
• Gyro: MPU6000 6-Axis
• Input: Up to 12S (50V) direct battery power Yes! 12S!
• USB type C
• DJI direct plug (6 pin)
• VTX pit mode switch – configured in Betaflight modes
• 5V or VBAT selectable for VTX and CAM power
• One wire Analogue Camera Control
• 4 Led pads (one at each corner) for easy LED installation – up to 40 LEDs on white and 100 LEDs in colour – perfect for FAI international races – shares 5V with 5V/2A BEC
• 6 UARTS, 4 full UARTS with RX AND TX pins
• 8 pin 4 in 1 ESC plug
• M5, M6 pads for additional motor outputs
• Buzzer pads for external buzzer
• Built in Betaflight OSD
• Boot button
• Logical pin layout for cleanest build
Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
VTX pit switch can’t control the DJI plug
Package Includes:
• 1x Wizz F7 HD 20×20 Flight Controller
• 6x M3 vibration damping
• 1x SH1.0 8PIN Cable (60mm) one side open ended
• 1x DJI Air Unit Cable (40mm)
Further information.
Size:
Some mini 20*20 Flight Controller with M2 holes on the markets, they are not suitable for 5″ inch racing frame. Although some are 20*20 size, but outer size are about 36*36 mm. (It’s same size with 30*30 Flight Controller)
We want to make a mini 20*20 flight controller with an outer size of 26*26 ~ 30*30 mm and using M3 screws.
Finally, we decided to add LED pads in each corner, outer dimension is 30*30 mm. It is worth to increase the size a little bit to reduce external LED control board.
Core:
MCU is STM32F722RET6 216MHz, F7 is a faster proessor and a lot easier to set up such as inverted signal.
Gyro is MPU6000 6-Axis, to reduce noise and avoid flying into space
Layout:
Logical layout makes welding easier, saving space for assembling parts, reduce annoying excess wires, it’s easy to makes for a clean build.
Left side of the above picture: upper front of the flight controller ⇧
On the right is the bottom of flight controller.
Camera:
Camera has four pads arranged at the front: C+ C- CS CC, can be welded directly to Runcam racer nano 2 or Foxeer Predator micro / nano v5。 CC (one wire camera control), enter camera setting through OSD without any setting.
Receiver:
Pads also located at the front, to avoid touching the ground on the left / right side of flight controller when crashing. Four pads G 5V R2 T2, can be welded directly to TBS Crossfire / Tracer.
VTX:
Located at the rear of the flight controller are solder pads for easy connection to the antenna. Four pads V+ V- VS T5, can be welded directly to TBS unify pro32 nano. Smart Audio – set on the Betaflight with T5 UART5, which can setting VTX via OSD.
VTX pit mode power switch – set on the Betaflight, which can turn the VTX ON/OFF with transmitter switch. Benefit for overheat when waiting for race start, and avoid your signal affecting other pilots when you was crashed.
Buzzer:
The + – poles are deliberately separated, which can welded the small buzzer directly to the flight controller without any wires
ESC plugs:
Designed at the rear bottom, theoretically, the plug wires can be shorter if set at the front, but it will mess around and reduce space for camera installation. Why rear bottom not rear above of flight controller? Because some peoples they tied the capacitor on the ESC main wires, it is easy to hit the ESC plug fall off when crashed.
Sort order of the plug are – + 1 2 3 4 CRT TELE, it can be plug directly to Aikon 20×20 ESC. The wires we provided is one side open end, convenient for you to use your favourite
UARTS:
6 UARTS, 4 full UARTS with RX AND TX pins
USB Type C
In 2021, there is no reason still using micro-b, although it’s smaller and lighter.
DJI digital FPV
Do you like Freestyle shooting? Simply plug-in DJI system, enjoy HD quality.
LED
LED pads at the four corners, specifically for professional racers to reduce troublesome connections.
(FAI competitions require 40 LEDs)
Voltage
Up to 12S (50V) direct battery power, enough for 4S or 6S.
Reviews
There are no reviews yet.